| Tip | ||||
|---|---|---|---|---|
| ||||
|
| Info | ||
|---|---|---|
| ||
The OpenMoteSTM is fully supported in OpenWSN. The OpenWSN builders build the OpenMoteSTM firmware nightly: |
The OpenMoteSTM Motes is designed by Micro-architecture and Integrated Circuit Lab (MICL) the University of Science & Technology in Beijing.
| Table of Contents | ||
|---|---|---|
|
Gallery
Overview
Components
| Name | Corporation | DataSheet | type | |
| U1 | LP5951MG 3.3V | Texas Instruments | lp5951 | Voltage Regulator |
| U2 | STM32F103RET6 | STMicroelectronics | Reference manual | Micro-Controller |
| U4 | CP2102 | SILICON LABS | CP2102 | USB to UART Bridge |
| U5 | Micro USB |
| Micro-USB_1_01 | USB | |||
| U6 | AT86RF231 | ATMEL | at86rf213 | radio |
| B1 | 74821245 | WURTH ELEKTRONIK | Chip-Balun WE-BAL | Balun |
| E1 | AN2051 | RainSUn | RainSun_AN2051 | antenna 1 |
| E2 | 734120110 | molex | 734120110_sd | antenna 2 |
XBee pin compatibility
20 Pins are left to fit with the definition of XBee's 20 Pin. Since XBee is widely used for wireless communication, the compatible pins make OpenMoteSTM to use the external boards for XBee, which existed for many kinds of, as well.
| XBee pin | XBee pin name | OpenMoteSTM pin | OpenMoteSTM pin name |
|---|---|---|---|
| 1 | VCC | 1 | VBAT |
| 2 | GPIO/UARTA_TX | 42 | PA9/USART1_TX(8)/TIM1_CH2(8) |
| 3 | GPIO/UARTA_RX | 43 | PA10/USART1_RX(8)/TIM1_CH3(8) |
| 4 | GPIO/PWM | 39 | PC8/TIM8_CH3 |
| 5 | RESET | 7 | NRST |
| 6 | GPIO / I2CA_SDA / PWM / ADC | 59 | PB7/I2C1_SDA/TIM4_CH2 |
| 7 | GPIO / I2CA_SCL / PWM / ADC | 58 | PB6/I2C1_SCL/TIM4_CH1 |
| 8 | DAC_OUT / ADC | 20 | PA4/SPI1_NSS/USART2_CK/DAC_OUT1//ADC12_IN4 |
| 9 | GPIO | 40 | PC9/TIM8_CH4/SDIO_D1 |
| 10 | GND | GND | GND |
| 11 | GPIO / ADC | 24 | PC4/ADC12_IN14 |
| 12 | GPIO / UARTC_RX | 54 | PD2/UART5_RX/SDIO_CMD |
| 13 | GPIO / UARTC_TX | 53 | PC12/UART5_TX/SDIO_CK |
| 14 | VREF | LQFP64 STM32 has not Vref Pin | |
| 15 | Differential ADC_DM | 8 | PC0/ADC123_IN10 |
| 16 | Differential ADC_DP | 9 | PC1/ADC123_IN11 |
| 17 | GPIO / ADC / SPI_MISO | 22 | PA6/SPI1_MISO/TIM8_BKIN.ADC12_IN6/TIM3_CH1 |
| 18 | GPIO / ADC / SPI_SCK | 21 | PA5/SPI1_SCK/DAC_OUT2/ADC12_IN5 |
| 19 | GPIO / ADC / SPI_MOSI / I2CB_SCL | 23 | PA7/SPI1_MOSI/TIM8_CH1N/ADC12_IN7/TIM3_CH2 |
| 20 | GPIO / ADC / I2CB_SDA | 25 | PC5/ADC12_IN15 |
Schematic and Layout
| Attachments | ||
|---|---|---|
|
...
After that, we should open IAR and select your project for stm32. Then click the green triangle button on the tool bar. The application will be downloaded into OpenMoteSTM and go into a debugging model.
...